Hermetically Sealed, Low IF, Wide Vcc, High Gain Optocouplers
The HCPL-6730 is a commercial grade two channel hermetically sealed optocoupler in a 20 pad Leadless Ceramic Chip Carrier with solder dipped pads. The solder contains lead.
The product is capable of operation and storage over the full military temperature range and may also be purchased with full MIL-PRF-38534 Class H or K level testing or from the DSCC SMD 5962-89785. The HCPL-6730 is manufactured and tested on a MIL-PRF-38534 certified line and the Class H and K versions are included in the DSCC Qualified Manufacturers List QML-38534 for Hybrid Microcircuits.
Each channel contains a GaAsP light emitting diode which is optically coupled to an integrated high gain photon detector. The high gain output stage features an open collector output providing both lower saturation voltage and higher signaling speed than possible with conventional photo-Darlington optocouplers. The shallow depth and small junctions offered by the IC process provides better radiation immunity than conventional photo transistor optocouplers.
The supply voltage can be operated as low as 2.0 V without adversely affecting the parametric performance. These devices have a 300% minimum CTR at an input current of only 0.5 mA making them ideal for use in low input current applications such as MOS, CMOS, low power logic interfaces or line receivers. Compatibility with high voltage CMOS logic systems is assured by specifying Icch and Ioh at 18 Volts.
Package styles for this die set in one, two or four channels are 8 and 16-Pin DIP through hole, 16-Pin surface mount DIP flat pack, and 20 pad leadless ceramic chip carrier. Most devices may be purchased with a variety of lead forms and plating options. See the datasheet for details.
Because the same electrical die (emitters and detectors) are used for each channel of each device listed in the datasheet, absolute maximum ratings, recommended operating conditions, electrical specifications, and performance characteristics shown in the datasheet figures are virtually identical for all parts. Occasional exceptions exist due to package variations and limitations and are as noted. Additionally, the same package assembly processes and materials are used in all devices. These similarities give justification for the use of data obtained from one part to represent other parts performance for reliability and certain limited radiation test results.
- Commercial Grade, Two Channel, 20 Pad Leadless Ceramic Chip Carrier
- Performance Guaranteed from -55 degrees to 125 degrees C
- High Radiation Immunity
- Reliability Data
- MIL-PRF-38534 Class H and Class K Available
- Five Hermetically Sealed Package Configurations Available
- One and Four Channel Devices Available (different package)
- Low Input Current Requirement: 0.5 mA
- High Current Transfer Ratio: 1500% Typical @ IF = 0.5 mA
- Low Output Saturation Voltage: 0.11 V Typical
- 1500 Vdc Withstand Test Voltage
- Military and Aerospace
- High Reliability Systems
- Transportation, Medical, and Life Critical Systems
- Telephone Ring Detection
- Microprocessor System Interface
- EIA RS-232-C Line Receiver
- Voltage Level Shifting
- Isolated Input Line Receiver
- Isolated Output Line Driver
- Logic Ground Isolation
- Current Loop Receiver
- System Test Equipment Isolation
- Process Control Input/Output Isolation
- Harsh Industrial Environments
|CMR (min.) (V/µs)||1000.0|
|CTR Min. (%)||300.0|
|IF Min. (mA)||0.5|
|Input Current Ma Uom||mA|
|Max Qty of Samples||2|
|Package||20 Terminal Hermetic LCCC|
|Product Type||Hermetic High Gain|
|Prop Delay (tPHL) Max. (µs)||100.0|
|Prop Delay tPHL Uom||µs|
|Prop Delay (tPLH) Max. (µs)||60.0|
|Prop Delay tPLH Uom||µs|
|Data Rate||100 Kb/s|
|Prop Delay (tPHL) Max. (µs)||100.0 µs|
|Prop Delay (tPLH) Max. (µs)||60.0 µs|
|IF Min. (mA)||0.5 mA|